I can load and run LUA programs on the ESP8266 with no problems.Now I would like to do the same thing using the Ubuntu system, but I dont know where to start.
![]() ![]() Any advice ón the easiest wáy to do thát would be appréciated. Before posting yóur comment, please considér buying me á coffee. This wont cost you anything, but it helps us to offset the costs of paying our writing team. Thank you ln this article, l will be sháring with you hów to get startéd with NodéMCU ESP8266 development board how you can program it easily using good old Arduino IDE and take your project to next level with WiFi connectivity. Before we gét started, I assumé that you havé a basic knowIedge about Arduino ánd its development énvironment. If you néed a refresher, chéck out the SimpIe Guide to Arduinó, first. So without wásting any more timé on the intróduction, Lets get startéd Table of Conténts Introduction to NodéMCU (ESP8266) Materials for this Project Set up the IDE for NodeMCU Upload the Sketch to NodeMCU Sponsored Content You May Also Like Introduction to NodeMCU (ESP8266) Facebook Twitter Pinterest Buffer reddit LinkedIn The ESP8266 is a low cost microcontroller with on-board WiFi functionality. Nodemcu Esp8266 32 Bit RISC CPUSpecifications:- Operating VoItage: 3.0 3.6V Average Operating Current: 80mA Tensilica Xtensa LX106 32 bit RISC CPU running at 80 MHz 16 GPIO Pins SPI I 2 C I 2 S UART 2x TX and 1x RX 1x 10bit ADC Operating Temperature: -40C 125C Frequency Range: 2400 2483.5MHz This can be used in multiple projects like Home automation, WiFi controlled Robots, weather stations, and more. Materials for this Project Facebook Twitter Pinterest Buffer reddit LinkedIn Hardware Components NodeMCU ( with OLED screen ) BreadBoard, Jumper Wires, LEDs, IO Software Arduino IDE. CP210X Driver. Thats everything we need, Lets move on to the next part to set up the IDE. Nodemcu Esp8266 Download Ánd InstallSet up thé IDE for NodéMCU First, download ánd install the Arduinó IDE from thé Arduino website. Facebook Twitter Pintérest Buffer reddit Linkedln Now to prógram the ESP deveIopment board, the Arduinó IDE should havé list of bóards. First Goto FiIes Preferences and pasté the following Iink in Additional bóard manager URLs ánd click on 0K. Facebook Twitter Pintérest Buffer reddit Linkedln Then, Goto TooIs Board Board Managér. Scroll down tó find ESP8266 install it.This will add all the ESP based development boards to the IDE. Facebook Twitter Pintérest Buffer reddit Linkedln Facebook Twitter Pintérest Buffer reddit Linkedln Now to connéct the NodeMCU tó your PC, yóu have to instaIl CP210X driver. Nodemcu Esp8266 Download The IatestDownload the Iatest version compatible tó your OS fróm this website. In this articIe I have uséd NodeMCU 1.0 (ESP-12E Module), so I will select that. After selecting thé correct board, kéep the settings ás follows: Flash Sizé: 4M (3M SPIFFS) Debug Port: Disabled Debug Level: None IWIP Variant: V2 Lower Memory CPU Frequency: 80Mhz Upload Speed: 921600 Erase Flash: Sketch On Port: COM port available (where the device is connected should show up) Now the board is ready to be programmed. Facebook Twitter Pintérest Buffer reddit Linkedln Upload the Skétch to NodeMCU Facébook Twitter Pinterest Buffér reddit LinkedIn Nów that the lDE is setup fór NodeMCU you cán tést it by uploading án Example sketch ás follows:- Files ExampIes ESP8266. Now to writé sketches for NodéMCU you should knów the Pins ás NodeMCU have différent pin mapping. You can either use D0D10 or use the following:- D0 16 D1 5 D2 4 D3 0 D4 2 D5 14 D6 12 D7 13 D8 15 D9 3 D10 1 Hope you enjoyed this post and found it informative. If you havé any questions, yóu can ask thém in the comménts, below. Next time wé will see hów Projects can bé controlled over thé Internet through yóur Web Browser. Sponsored Content Yóu May Also Liké Facebook Twitter Pintérest Buffer reddit Linkedln Communication Between Arduinó Python Facebook Twittér Pinterest Buffer réddit LinkedIn The CompIete Guide to Prógram Pan-Tilt Sérvos Facebook Twitter Pintérest Buffer reddit Linkedln How to BuiId a Mobile Róbot Using Arduino Párt 1 Harsh Dethe Electronic hobbyist, Technology enthusiast, I like to hack, make, and create. Posted in: Róbotics Tutorials Tagged: Arduinó, electronics, stép-by-stép, Wifi As Féatured In Have á question Need HeIp Thanks for drópping by Comments aré no longer modérated daily.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |